The Face Shop Rice Water Bright Cleanser 150ML

The case itself is quite the eye catcher, and it does leave room for upgrades. It came with many different screws upon arrival and was not at all damaged.
Installation of my parts was easy enough and the case even came with motherboard raisers, however these are removable if you choose.
The fans it came equipped with, while pretty, don’t move as much air as I would personally like them to (around 1000 rpm and you cannot change the speed). Luckily, your able to replace them if you wanted to, like I did.
The tempered glass is very prone to smudging so handle it with care or be prepared to maintain it with glass wiped. The glass case also came with two triangular “Caution, tempered glass” sticker on each of the broad sides. Some people like to keep them, however I tried to remove them. This caused the sticker to tear and look horrible. Luckily, an adhesive remover and a sharp knife or razor is all it takes to have the class looking clean again.

A couple things I want to note: YOU CANNOT have the RGB switch and the reset switch hooked up at the same time. Its one or the other.
Cable management is a little trickier in this case than in others.
If you switch the rgb case fans with your own be prepared to do some work, as it comes with its own controller.

Overall, this is a nice case with good eye candy quality and good case features, but I wouldn’t recommend it to someone who is new to building pc’s, as it can easily become overwhelming.

It’s too bad the case’s rgb settings don’t remember your selection, but you can switch them on easily enough every time you boot. Press the front panel rgb button nine times to bring the fans to slow color cycle, otherwise it’s flashy and annoying. Even though it doesn’t sync with the motherboard, the slow cycle option looks nice anyway.

The motherboard screws and the SSD screws are mislabeled on their provided directions. Make sure to use the correct screws, otherwise you might get loose screws stuck in your motherboard.

The metal is actually pretty decent quality, not just cheap sheet metal that will cut.

Cable management in this is hit and miss. Some cable management spaces are positioned well, and some spaces that should have cable management spaces don’t have them.

The glass is good quality, but it comes with stickers that are difficult to get off. I had to use nail polish remover to get the sticker gunk off of the nice glass.

Don’t get this case if you’ll want to replace the front fans. It’s not going to be worth it to take apart the whole case to get to the front fans.

Airflow seems a bit too open. I wanted to achieve a positive case pressure to avoid dust issues, and to achieve good airflow in the right areas. I’m not sure the case is enclosed enough to allow this. I added another fan on the top slot to get more inward airflow. It seems to have helped, however air still seems to be going inward into the open vents (negative air pressure). I also replaced the back fan to have the inside components all sync with ASUS Aura.

Plenty of space in the case, it does the trick, it just has some frustrations that could have been avoided with a little better design.

Love this case. I was looking for a decently priced tempered glass panel case for my VR build. Found this and jumped on it. Very nice, built in fan controller for the RGB fans. My only issue with it is the wiring for the fans and fan controller are not the standard that you will find on a motherboard. It still uses 4 pins, but a different connector. I would have liked to see an option for running the LEDs from the board to the fan controller to bypass the LED function of the fan controller. I ended up splicing the wires to an existing splitter that I had laying around. This made it so that I can run the fan LEDs together with my other LEDs on the liquid cooler and motherboard. Makes for a much better flow, as the limited effects of the built in controller are nothing compared to what comes off the board. Wouldn’t recommend doing that to anyone not experienced with electronics, or these 5050 LEDs in general, but it’s not too difficult if you watch the wires and read the pins on the fan controller. It makes a good case a great case.

I was hesitant to try out a new manufacturer for my case selection of my recent build, but I decided to take a gamble and boy did it pay off. The case is beautiful, from the tempered glass sides to the 4 LED fans and with a price point that makes it even more enjoyable.

The LED fans have a great range of options from the colors (red, blue, green, white, purple, yellow) to the effects (strobe, pulse, cycle, static color and my favorite rainbow/gradient) and is activated by a button on the top of the case.

The positioning for the power supply leaves plenty of room in a covered area for any extra cables to be stored (for us cable management people). Finally, the RGB controller is in a great place to stay out of the way from your cable management desires.

Most cases running around this price lack the amount of fans, and the attention to detail.

PROS:
Tempered Glass
Feels sturdy
Comes with 4 Fans (LED!!)
Great SSD placement

CONS:
Tempered Glass is fingerprint magnet
The LED fans reset (color and effect) when you turn off the Power

In short, you will surely love staring at this case when the system is on and the fans are cycling through their colors.